How To Put A Chain Back On Electric Chainsaw? Do you want to know how to re-chain an electric chainsaw? It is achievable, but it will take a lot of work, and it will require a specific type of know-how to pull it out with a bit of elegance and a lot of elbow grease.
A chainsaw is essential to acquire whether you are an active DIYer who enjoys woodcutting projects or a sensible homeowner who wants to cut wood to fuel the fireplace. However, it will grow heated and loose, as with all machines that rely heavily on chains.
It will ultimately cause the chain to tumble or leap off the guide bar. It may also come off if it becomes clogged with wood chips.
Another possibility is that you used it without sufficient tension and got too loose. Any of these events indicate that the chain must be changed.

Things To Consider Before Starting:
Always keep safety in mind while working with tools like chainsaws, even if they aren’t plugged in. When changing chains, always wear gloves since the teeth may be pretty sharp, and cutting yourself would undoubtedly spoil your day.
Your chainsaw’s instruction manual will give all the information you need to calculate the gauge and pitch of the guide bar.
You may verify these figures by thoroughly inspecting your chainsaw bar. Most will display length, drive links, gauge, and pitch information.
The new chain must be compatible with your guide bar. Remember that various bars need different chains. A chain of the proper length is necessary for safety reasons. If your chainsaw’s chain is dull, you may sharpen it rather than replace it.
How To Put The Chain Back On An Electric Chainsaw?
These steps will show you how to install a chainsaw chain, replace a chainsaw chain, and put a chainsaw chain on a chainsaw. Each may seem different, but their procedures are the same.
The chainsaw chain keeps leaping off the bar for a variety of reasons. It may need sufficient lubrication, or it may be overheated.
Adjusting the chainsaw chain will be simple if you have the correct tools.
Remove Sawdust:
Before pulling the chain from the chainsaw, ensure that all debris and wood chippings lodged in the chain or elsewhere are removed. Cleaning all the cracks and crannies requires a large paintbrush with a three-inch brush.
Loosen The Cutting Bar:
Remove the old chain from the saw. To do this, you must first loosen the cutting bar. The method utilized varies according to the saw. Still, manufacturers use two primary ways: those who need tools and those who do not.
There will be a huge knob on the tool-free saw that you may turn to release the bar and de-tension the chain. This part of the saw is often seen on the right. For saws that need tools, a pair of nuts or bolts are usually situated on the side of the chainsaw where the bar joins the body.
De-Tension The Chain:
You must now de-tension the chain after loosening the cutting bar. Check the area around where you loosen the cutting bar for a screw or a knob. Turning this causes the chain on the cutting bar to loosen.
Loosen the chain all the way, and you’ll be able to remove it entirely off the cutting bar. Please continue to work it off until it is completely free.
Removing The Chain:
The chain will remain attached to the little sprocket within the saw after being withdrawn from the cutting bar. When seen from below, the chain and sprocket of a saw may be seen running through a slot in the saw. Using a screwdriver or your fingers, remove the chain from the sprocket, and it should now be free to be removed.
Putting The Chain Back On Your Electric Chainsaw:
You are now ready to install your new chain. The first thing to remember is to use a suitable chain for your electric chainsaw. Not all chains are ideal for all saws, and you should double-check that you have the proper chain.
Make a mental note of which way the chain travels on the saw. It is common practice to mark on the saw itself the route that the chain follows as it travels down the bar’s top, around the tip, and then down the bottom of all saws; nonetheless, the chain does follow this path.
It is necessary to guarantee that your new chain is installed correctly. Please take note of the direction in which the teeth are sharpened and any notations on the chain or packaging to ensure that it is properly fitted.
Mounting The New Chain:
Pull the new chain opposite the cutting bar over the sprocket. Insert the inner lugs of the chain into the slot on the cutting bar with care. Saw teeth should be installed clockwise around the cutting bar, beginning at the saw’s body and proceeding outward.
Tension The Cutting Bar:
You may now begin re-tensioning the cutting bar, ensuring that all the lugs remain correctly aligned in their holes. Continue tensioning the bar until you reach the manufacturer’s recommended tension. It usually allows for some slack – the chain should not be bar-tight.
Finally, re-secure the cutting bar by tightening the bolts or using the tool-free adjustment knobs. Even though most chains come pre-oiled, you should still check that there is sufficient chain oil in your saw.
Hand-move the chain back and forth to ensure it moves correctly. You are ready to re-plug the saw and put it through its paces. Run the saw carefully to grease the new chain, then make several test cuts to ensure that the new chain is cutting correctly. Stop, disconnect the saw, and check for problems if anything is stuck or doesn’t look right.
Conclusion:
The process of replacing the chain on an electric chainsaw may seem to be quite challenging at first. Still, as long as you keep safety in mind and take the appropriate precautions, you should be OK. Doing this correctly and securely should take, at most, a few minutes.
Replacing the chain on your chainsaw is a necessary aspect of maintenance that you will have to undertake sooner or later. Because you now know how to reattach a chain to an electric chainsaw, you won’t have to be as concerned about the matter as you were before.
Don’t miss to check our new post about Best rain barrel soaker hose in 2023.